Jib crane 0.125 tons

Construction type

pillar, wall, wall traveling, special-purpose

Load capacity, t.

0,125 (up to 16.0)

Boom outreach, m

up to 12.0

Angle of rotation, dg.

up to 180/270/360°

Type of drive

manual/electric

Lift height, m.

up to 36.0

Design number of full load cycles according to ISO 4301/1

A2 and above

Environmental class according to GOST 15150-69

U1 (outdoors)/U2 (under a canopy)/U3 (indoors)

The design of the crane

General-purpose industrial version/Fire-safe version/Explosion-proof version

Fill out the questionnaire for the jib crane

от 48 750 ₽*

Cost calculation

Scope of delivery

crane boom (console) — 1 pc.
crane column with lower support flange* — 1 pc.
crane control box** (with the exception of cranes in the VZI version)
gear motor 1-2 pcs.** (depending on the boom departure and lifting capacity of the crane)
cable products**
hoist (when delivered complete with a hoist)
power supply to the crane (optional)
power supply to the hoist (optional)
other parts (the list of components depends on the configuration and set of options of the crane you ordered and may differ from the one given in this section of the site)
crane documentation (passport, crane operation and installation manual, passports and instructions for individual crane components manufactured at other enterprises and supplied with this crane, packing list, waybill).

* For cranes on columns.
** For models with electric drive.

The above configuration is basic and may differ significantly from the actual one. If you need complete information on this issue, please contact the nearest sales department.

List of additional options

By default, the cranes are manufactured in standard configuration. But depending on their technical characteristics and operating conditions, the plant manager can recommend to supplement the standard equipment with one or another set of options. Below is a brief description of them and the rationale for their installation.

Option Name	Option Description
Load Limiter	Serves as an additional safety device alongside limit switches and load drop protection devices in case of phase failure. Typically installed when handling various loads with unknown weights. If the load exceeds the hoist’s capacity, the limiter halts the lifting process. Available for cranes equipped with an electric hoist as the limiter is mounted on the hoist’s lifting mechanism.
Sound and Light Alarms	Activated when the jib crane is switched on, warning employees to leave the danger zone. Depending on workplace conditions, either light or sound alarms are recommended. Available only for electric jib cranes.
Radio Control	Allows remote control of the crane using a remote controller. Available for electric jib cranes or cranes equipped with an electric hoist. The delivery includes a 6-button remote controller with an emergency stop button and a radio signal receiver (mounted on the hoist or near the crane’s control box).
Motor with Brake for Jib Rotation	The integrated brake stops the jib at the desired position without inertial movement. Manual fixation at a precise point is impossible. The brake is hidden within the motor-reducer system. Recommended for cranes with outdoor placement categories U1 and U2 to prevent unintended jib movement in parking position during strong winds or other external factors.
Hoist Parking Canopy for Outdoor Use	Used for cranes in outdoor placement category U1 to protect the electric hoist from direct precipitation. Recommended by crane and hoist manufacturers since standard hoist designs typically lack alternative precipitation protection.
Full Span Hoist Canopy for Outdoor Use	Protects the electric hoist across the full span of the crane in outdoor placement category U1. Recommended by crane and hoist manufacturers for additional precipitation protection.
Power Cut-Off Switch on Crane Column	Enables switching crane power on and off. Located approximately 1500 mm from the lower flange of the crane. Consists of a two-button post housed in a protective (metal) casing.
Electric End Switches for Hoist Travel on Jib	Used to limit the travel distance of the electric hoist along the crane’s jib.
Anchor System for Crane Foundation Fixation	This option applies during the installation phase. Anchors secure the crane to its foundation. For prepared foundations, an anchor system is typically offered. For unprepared foundations, mounting studs are used instead.
Load Drop Protection Device for Phase Failure	An additional safety device alongside load limiters and limit switches.
Crane Operation Parameter Recorder	Records crane operating conditions, including modes, duration, and load capacity. Installed only on cranes equipped with electric wire rope hoists.
Crane Operation Time Indicator	Tracks crane operation time to schedule maintenance, minor repairs, and major overhauls. Integrated into or mounted on the control box door.
Frequency Regulation for Jib Rotation Speed	A frequency converter installed in the control box allows for adjustable jib rotation speed within a specified range. Also enables smooth start and braking.
Engine Cooling System	Recommended when installing a frequency converter, which significantly reduces the standard movement speed of the crane, to prevent motor overheating.
Input Choke	Smooths voltage spikes and reduces amplitude fluctuations in the AC supply. Reduces current ripple amplitude consumed by the frequency converter.
Platform and Ladder for Hoist and Crane Maintenance	For jib cranes taller than 3 meters, it is recommended to include maintenance access solutions such as a horizontal platform at human height from the jib and a ladder welded to the crane column. This facilitates hoist maintenance, oil changes, and other service operations.
Heated Crane Control Box	Enables jib crane operation at air temperatures down to -20°C. Mandatory for cranes operating below -10°C. Requires the additional installation of a frequency converter.

Description

The 0.125 ton jib crane is a compact and versatile solution for lifting and moving light loads in confined spaces. The crane has an outreach of up to 12.0 meters and can move loads over a radius of up to 360 degrees to provide optimum coverage of the work area. The lifting height is 36.0 meters, making it a versatile equipment for a variety of applications. Can be supplied with a wall mount. Check the specifications on the profile page: https://грузоподъем.рф/catalogs/krany-konsolnyy-nastennyy.

Cantilever cranes with a lifting weight of 0.125 tons provide accurate and smooth load handling, which is especially valuable when working with delicate materials. Most often they are supplied with manual drive, but on request they can be electrically driven to increase efficiency. These cranes provide a reliable and safe solution for lifting tasks of varying complexity.

Any questions?

Leave a request for a consultation with a technical specialist: